maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. f or capacitive load, derate current by 20% type number symbol es 5 a es 5 b es 5 c es 5 d es 5 f es 5 g es 5 h es 5 j units maximum recurrent peak reverse voltage v rrm 50 100 150 200 300 400 500 600 v maximum rms voltage v rms 35 70 105 140 210 280 350 420 v maximum dc blocking voltage v dc 50 100 150 200 300 400 500 600 v maximum avera g e forward rectified current see fig. 1 i (av) 5 .0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) @t l = 100 o c i fsm 1 5 0 a maximum instantaneous forward voltage @ 5 .0a v f 0.95 1.3 1.7 v maximum dc reverse current @ t a =25 o c at rated dc blocking voltage @ t a =100 o c i r 10 500 ua ua maximum reverse recovery time ( note 1 ) trr 35 ns typical junction capacitance ( note 2 ) cj 45 30 pf typical thermal resistance (note 3) r ja r jl 47 12 o c /w operating temperature range t j -55 to +150 o c storage temperature range t stg -55 to +150 o c notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied v r =4.0 volts 3. units mounted on p.c.b. with 0.6? x 0.6?(16mm x 16mm) copper pad areas smc ( do-214ab ) dimensions in inches and (millimeters) .128(3.25) .108(2.75) features m echanical data ? case: do-214ab (smc) molded plastic body ? epoxy: ul 94v-0 rate flame retardant ? lead: lead formed for s urface mount ? mounting position: any ? s up e r f a st swi t chi ng t i m e f o r h i gh e ff i cie n cy ? lo w f o r w a r d vol t ag e d r op and h i gh cur r e n t cap ab ili ty ? lo w r e ver se l e a kag e cur r e nt ? p l a sti c m a t e r i a l ha s u l f l a mm ab ili ty classif i cat i on 94 v -0 http://www.trr-jx.com es5a-es5j surface mount superfast rectifiers
fig.2- maximum non-repetitive peak forward surge current peak forward surge current. (a) 1 10 100 150 125 100 75 50 25 0 number of cycles at 60hz 8.3ms single half sine wave o (jedec method) at t l =120 c fig.1- maximum forward current derating curve average forward current. (a) 80 90 100 120 140 150 130 110 0 4 6 2 o lead temperature. ( c) resistive or inductive load p.c.b. mounted on 0.6x0.6"(16x16mm) copper pads 10 1 0 100 105 75 45 30 15 90 60 fig.5- typical junction capacitance junction capacitance.(pf) reverse voltage. (v) es 5 a - d es 5 f - j 0 tj=25 c f=1.0mhz vsig=50mvp-p fig.4- typical reverse characteristics 0 20 40 60 80 100 120 140 10 100 1000 1 0.1 0.01 percent of rated peak reverse voltage. (%) 0 tj=100 c 0 tj=75 c 0 tj=25 c instantaneous reverse current. ( a) fig.3- typical instantaneous forward characteristics instantaneous forward current. (a) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.01 1 10 100 0.1 forward voltage. (v) es5a - d es5f - g 0 tj=25 c pulse width-300 s 1% duty cycle es5 h - j fig.6- typical transient thermal impedance o transient thermal impedance ( c/w) 1 0.01 0.1 10 100 0.1 10 1 100 t, heating time (sec.) fig.7- reverse recovery time characteristic and test circuit diagram 50 w noninductive 1w non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 w noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm http://www.trr-jx.com characteristic curves (t a =25 unless otherwise noted) es5a-es5j surface mount superfast rectifiers
|
